# Control-Panel Carrier — Bounded Electrical Verification (rev C, 2026-11-12)

> Rev C applies independent-review corrections F1–F6 (review k9). Documentation only; no schematic, placement or copper change. **No electrical or fit release is claimed: the parent holds routing/electrical/fit release until every gate below is closed.** Parent heater: DO NOT ENERGIZE.

Source IDs refer to `carrier-capture-source-audit.md` rev B section B1. Rail bound used: parent 3V3 = 3.234–3.366 V. **F5: this is a working ASSUMPTION, not a guaranteed bound** — the Pico datasheet gives no numeric 3V3 tolerance, and the RT6150 ±1 % reference figure ignores feedback-divider tolerance, ripple and load/line regulation. Closed only by G-P8 measurement. VOL = 0.4 V. Parent heater: DO NOT ENERGIZE. Proposed firmware limits are proposals, not imposed.

## 1. Verification table
| # | Check | Formula / basis | Result | Verdict | Source |
|---|---|---|---|---|---|
| 1 | Effective bus pull-up per line (R3/R4 + M1 + M2) | 1/(1/4.7k + 1/10k + 1/10k) | 2.42 kΩ | Pass | S-OLEDSCH, S-ENCSCH, parent R3/R4 |
| 2 | Sink current at VOL (F3 corrected) | Bus side: (3.366−0.4)/2.42k = 1.226 mA; module side: each BSS138 conducts when bus is LOW, so each module 3.3V-side 10k also sinks ≈(3.3−0.4)/10k = 0.29 mA × 2 | **≈ 1.82 mA per line** at VOL 0.4 V (≤ 3 mA), worst bound incl. both module-internal 10k | Pass | I²C 3 mA limit; S-OLEDSCH, S-ENCSCH (BSS138 + 10k both sides) |
| 3 | Optical module pull-up allowance (F3 corrected) | Remaining 3 − 1.82 = 1.18 mA; single bus pull-up: R ≥ 2.966/1.18 mA; dual (BSS138 level-shifter) pull-ups: ≈ half each | **R ≥ 2.5 kΩ** if single; **≥ 5 kΩ each** if bus-side + module-side pair. Example 10k+10k optics → total 2.41 mA | Bounded — G-E1 | S-1334 (value unpublished) |
| 4 | Max bus capacitance | C = t_r/(0.8473 R); t_r 300 ns (400 kHz) / 1000 ns (100 kHz); module-side resistors do not aid rise (BSS138 off when high) | 146 pF / 487 pF conservative (unchanged); optics pull-ups only raise this | Bounded — G-E2 | I²C rise-time definition |
| 5 | Pull-up rail | Bus-side 10k halves tie to QT V+ = parent 3V3; module 3.3V-side 10k isolated by BSS138 | All bus pull-ups on parent 3V3 | Pass | S-OLEDSCH, S-ENCSCH |
| 6 | Addresses | ADS1115 ADDR=GND 0x48; TCS34725 0x29; encoder 0x36 (+SJ8/SJ9/SJ1 → 0x36–0x3D); OLED SA0 high 0x3D (SJ3 → 0x3C); MAX31856 is SPI | No collision at defaults. Do not close encoder A1+A2 (0x3C) or A0+A1+A2 (0x3D) | Pass with constraint | S-OLEDSCH, S-ENCSCH, S-TCS, parent U2 |
| 7 | OLED current | AP2112 Iq 0.08 + APX803 0.04 + IDD 0.3 + IBAT 28.9 (100 % pixels) + LED/pull bounds 1.32 | 17.7 mA typ (50 % pixels) / 30.6 mA max | Pass (IBAT spec is at VBAT 3.5–4.2 V; module runs ~3.2 V) | S-UG2864, S-AP2112, S-APX803 |
| 8 | Encoder current | AP2112 0.08 + SAMD09 3.01 + LEDs/pulls 1.65 + NeoPixel 3×14.5 + 1 | 3.7 mA typ (pixel off) / 49.2 mA max | Pass | S-SAMD09, S-SK6812 |
| 9 | Carrier total on parent 3V3 | 7 + 8 + bus-side pull-ups 4×3.366/10k | 21.4 mA typ / 81.2 mA max | Pass | rows 7–8 |
| 10 | Parent 3V3 external headroom | 300 mA − (81.2 + U2 0.3 + U3 2.0 + R1/R3/R4/R5/R24 bounds 2.4 + TCS 0.33) | Known 86.3 mA (math re-checked OK); 213.7 mA left for optics LED + optics regulator + any J10 probe. MAX31856 2 mA max (converting) now verified from full ADI datasheet (F6) | Bounded — G-E3 | S-PICO, S-MAX31856 (full ADI datasheet), S-TCS |
| 11 | Module 3.3V rail, worst | V3V3min − [XH 4×20 mΩ×I_h + harness 2×84.2 mΩ/m×L×I_h + SH (4×40 mΩ + 2×0.05 m×538 mΩ/m)×I_m + AP2112 0.8 Ω×I_m] | Encoder 3.173 V, OLED 3.192 V at L = 0.3 m; 3.164 V / 3.183 V at L = 1.0 m (parent and carrier copper excluded) | Pass for logic | S-XH, S-SH, S-AP2112 |
| 12 | OLED auto-reset threshold | V_mod − VTH(rising, max + 40 mV hyst) | APX803-26: +0.49 V; -29: +0.17 V; -31: ≈0 V (marginal) | Pass if -26/-29; G-P3 | S-APX803, S-ADA-POR |
| 13 | SAMD09 supply / BOD (F2 corrected) | seesaw @20e2892 board config for product 4991 has no BOD writes; SAMD09 factory fuse BOD33 LEVEL 7: falling 1.64/1.67/1.69 V (min/typ/max), release ≤ 1.75 V (not LEVEL 48) | Worst module rail 3.164 V − 1.75 V = **≈ 1.41 V margin** on public evidence. Production fuse values on shipped units unknown (note only) | Pass (public evidence); note | seesaw @20e2892 (review k9), S-SAMD09 BOD33 table |
| 14 | NeoPixel supply (F1 corrected) | SK6812MINI-E VDD min 3.7 V vs module 3.3V rail ≤ 3.35 V | Below spec inherent to 4991 module (NeoPixel fed from AP2112 3.3V output). **5 V on V+ would NOT fix it** (AP2112 still outputs 3.3 V) and would put 5 V on bus-side pull-ups → unsafe for Pico GPIO. **Keep V+ = 3V3.** Not guaranteed | Info — inherent, not guaranteed pass | S-SK6812, S-ENCSCH, S-AP2112 |
| 15 | OLED supply (F4 corrected) | VBAT min 3.3 V vs conditional rail 3.164–3.35 V; VDD recommended max 3.3 V, abs max 4 V | VBAT up to **136 mV below** minimum; VDD up to +1.5 % over recommended max (within abs max). Inherent module condition; Adafruit states tested working; **not a guaranteed pass** | Info — inherent | S-UG2864/SSD1306, S-ADA326 |
| 16 | Logic levels | Bus high = parent 3V3; BSS138 gates at module 3.3V; NeoPixel DIN VIH 0.7×VDD | Compatible | Pass | S-OLEDSCH, S-ENCSCH, S-SK6812 |
| 17 | Startup timing | APX803 holds RES# 140–280 ms after VTH; panel needs 100 ms after VCC stable before Display ON | Proposed firmware: wait ≥ 400 ms after power-up before OLED init; retry 0x36 probe for seesaw | Proposal | S-APX803, S-UG2864 |
| 18 | QT cable current | 49.2 mA worst vs 1.0 A @AWG28 | 4.9 % of rating | Pass | S-SH |
| 19 | QT cable conductor | SSHL-002T-P0.2 accepts AWG32–28, OD 0.4–0.8 mm | Conductor is ≤ AWG28 (≤ 0.321 mm, ≤ 0.081 mm²); 50 mm = 10.6 mΩ (28) to 26.9 mΩ (32) | Bounded — G-P4 | S-SH, S-4399 |
| 20 | XH harness (proposed 24 AWG) | SXH-001T-P0.6: AWG28–22, insulation OD 0.9–1.9 mm; rated 3 A @AWG22 only | 24 AWG in range; 81 mA load; 13.7 mV/m loop drop at 81 mA | Pass with wire OD gate G-P5 | S-XH |
| 21 | Bend / strain | No bend-radius figure published by Adafruit or JST; JST: ≥ 10 mm straight from housing end face, slack, no load on crimps | 50 mm QT cable leaves ≤ 30 mm for bends | Enclosure gate G-P6 | S-JSTHAND |
| 22 | Pin mapping | J9 n ↔ cavity n ↔ J1 n; QT pin 1 GND / 2 V+ / 3 SDA / 4 SCL | See audit B5 continuity map | Pass (test G-P7) | S-XH, S-SH, S-4399 |
| 23 | Hot-plug / protection (F6) | No carrier inrush limiting, reverse-polarity or ESD protection; XH keyed but a mis-built harness could reverse 3V3/GND | Connect/disconnect only with parent powered OFF; continuity-test harness (G-P7) before first power | Constraint | S-XH, carrier netlist |

## 2. Proposed (not imposed) firmware load limits
- NeoPixel: either (a) total channel sum ≤ 255 (one channel at full) → ≤ 15.5 mA, or (b) the manufacturer's 12 mA-version guidance of ≤ 70 % grayscale when all three colours are on → ≤ 31.5 mA. Option (a) keeps carrier max ≤ 52 mA.
- OLED: avoid long full-white screens (28.9 mA max, burn-in per S-ADA326); blank when idle.
- I²C clock: 100 kHz until G-E2 is measured; 400 kHz only if the measured rise time is ≤ 300 ns.

## 3. Residual gates
**Electrical (need parent decision or measurement):**
- G-E1 Optical module pull-up value (exact part not selected; provisional Adafruit 1334). Requirement: ≥ 2.5 kΩ if single pull-up per line; ≥ 5 kΩ each if dual level-shifter pull-ups (F3).
- G-E2 Measured I²C rise time (30–70 %) on SDA/SCL at the Pico with everything connected. Requirement: ≤ 1000 ns (100 kHz) or ≤ 300 ns (400 kHz).
- G-E3 Optics LED current, optics regulator Iq, and whether a debug probe draws from parent J10 3V3. Requirement: combined ≤ 213 mA (300 mA recommendation).
- G-E4 CLOSED on public evidence (F2): seesaw @20e2892 writes no BOD; factory BOD33 LEVEL 7 (≤ 1.75 V release) → ~1.41 V margin. Residual note: production fuse values on shipped units not published.
- G-E5 CLOSED (F6): MAX31856 2 mA max converting, verified from full ADI datasheet.

**Physical-only unknowns (measure or inspect hardware):**
- G-P1 Delivered Adafruit 326 outline and hole pattern (CAD 29.21 × 31.75 mm vs product page 29.2 × 26.7 mm).
- G-P2 Physical B4B-XH-A No. 1 position against the carrier J1 pad-1 marking (rear-mounted).
- G-P3 APX803 threshold variant on the delivered OLED (read the SOT-23 marking).
- G-P4 Actual Adafruit 4399 conductor AWG/strand and insulation OD (not published).
- G-P5 Insulation OD of the chosen 24 AWG harness wire must be 0.9–1.9 mm.
- G-P6 Harness length, routing, 10 mm straight exits and slack (enclosure scope).
- G-P7 Continuity test per audit B5 on the built harness.
- G-P8 Parent 3V3 measured at the Pico under load (3.234 V minimum is an assumption, F5).

**Operating constraints (F1/F6):** keep QT V+ = parent 3V3 (never 5 V); mate/unmate harness and QT cables only with parent power OFF.

**Release status:** no routing, electrical or fit release is claimed; parent release remains held until all open gates close.
