# Final finite cable-only repair

Scope: fixed-endpoint >=15mm cable bows, attached loose guides, stock-length/service checks, records. **Nominal geometry PASS; no manufacturing, supplier-bend, tolerance, electrical or heater release.**

## Implemented
Child J2/J3, module/control centers and axial stack unchanged. No copper, child edits, shell cuts or purchases. Installed separate exact seven-cubic-segment cable reservations, diameter4mm ENGINEERING ENVELOPE, not sourced OD:

|Cable|Exit-to-exit length mm|Minimum centerline radius mm|Margin over15mm|
|---|---:|---:|---:|
|OLED|199.998286|15.494188|0.494188|
|Encoder|199.999330|15.463431|0.463431|

Analytic derivatives and bounded scalar minima used. Cable separation lower bound7.047mm after both2mm radii and0.4mm discretization allowance: no crossing.

Two installed one-solid PETG loose guides: bore7, axial length3, wall2, bearing tongue1mm. They replace the lower1mm carrier washers at panel-local(-46,-17,-22.6) and(51,-17,-22.6), reuse existing ISO7045 M3x6 bolts,3.5mm clearance bores and3.3814mm thread engagement. Two other custom washers and all16 module washers remain. No added standard hardware. These are loose guides, not compression clamps or certified strain relief. Near-straight3mm guide zones preserve over1.2mm nominal wire-envelope clearance without forcing a kink.

Guide centers: OLED(-64.294895,-8.340368,-19.556702), encoder(68.856370,-3.598339,-34.408056). A measured2.961272mm3 right-guide/gusset overlap was repaired with an arm detour through(60,-7,-21.1). Final guide/support gap1.6186mm, zero overlap; original result is historical only.

## Source datum and stock limits
Adafruit-distributed https://cdn-shop.adafruit.com/product-files/4424/4424-ds.pdf (XS191102-A1,V1.0,2019-11-2) visually dimensions200+/-5mm **between housing wire-exit faces**, not plug tips. Wire1571#28; cut210+/-5mm. PDF and image saved. Nominal path uses that drawing datum; precise four-wire fanout/keyed seating remains envelope-level.

Fixed-endpoint/fixed-guide-center195/205mm alternatives were solved and screened. Encoder radius minima15.1983/15.1907mm; OLED15.1974/15.1992mm. Accepted controls: stock-tolerance.json encoder rows; oled-stock-local.json OLED rows. Rejected searches in other files are historical, not accepted geometry. Worst extreme conservative mesh gap0.05368mm is195mm OLED to left support; positive nominal fit but inadequate manufacturing allowance. All four extreme guide-clearance bounds exceed1.035mm.

Endpoint chords OLED48.043549mm, encoder43.142030mm. Nominal geometric excess151.954738/156.857300mm, distributed in broad3D bows, not50mm folded loops. Over195–205mm stock this geometric excess is146.956–156.956mm OLED and151.858–161.858mm encoder. This is not usable extraction travel.

## Verification and tolerance budget
133 exact candidate checks completed using bounding-box broadphase and individual cable-segment/solid narrowphase, not enormous all-pairs compounds. final-checks.json supersedes repaired-guide pairs.17 additional final guide/parent/service checks completed, no overlap, minimum0.678545mm. Actual available native shell/population and selected carrier/supports included. Parent frame material before added blind pilots is a conservative clearance obstacle.

Minimum exact cable/nonmating-solid gap0.632325mm encoder/core; source0.06mm finish gives0.572325mm to finished face. OLED cable/support1.011228mm; OLED guide/frame0.678545mm. Revised encoder guide/cable1.237472mm, OLED guide/cable1.308643mm. No remaining unintended overlap detected in checked nominal pairs. Foot/core gap0.06mm is intended finish allowance; feet bear on finished face. Existing bolt head/guide contact has zero common volume.

**Mating-end allowance does not pass:** OLED SH external-envelope/source connector gap0.054mm. PH/source-header external envelopes overlap213.885mm3 per pair because solid envelopes lack actual mating cavities. Conservative mating gap0mm; at assumed combined0.5mm allowance, -0.5mm. Do not infer keyed seating/contact engagement from these envelopes.

Engineering allowance0.25mm per assembly, combined0.5mm, is NOT a supplier tolerance. Nominal encoder cable/finished-face residual0.072325mm; guide/frame residual0.178545mm.195mm OLED/support bound less allowance=-0.44632mm. Full tolerance release remains held despite nominal geometric fit.

## Installation/service
Power off. Thread unmated SH through loose guide BEFORE mounting/mating; PH end will not fit. SH5x2.1mm projected cross-section through bore7: exact20mm axial sweep gap0.788451mm, zero overlap. No wire squeezing/ties. Guide foot replaces lower washer under existing bolt. Mate/unmate by housing.

For service remove approved front access/knob, unplug, remove lower carrier screws, unthread SH, then move unloaded guide inward2mm, inward4/outward2mm, inward4/outward5mm. Sampled exact support and parent checks are saved; minimum support gap1.6186mm. Prior carrier withdrawal remains unchanged. These are rigid-envelope stages, not fatigue/human-finger qualification.

## Evidence/replay
Canonical final sources: OLED-bow.build123d, encoder-bow.build123d, OLED-guide.build123d, encoder-guide.build123d. Execute each to obtain result. author_bows.py is historical and must NOT overwrite final guide sources. verify_bows.py, final_checks.py and close_cables.py replay measurements/export from saved source scene/cache. selected-controls-cables-complete.step has169 valid nominal reconstructed solids, not manufacturing data. Installed readback: unit scale; relative O=(0,-57.5,61.5)mm,Rx67.1354918781deg; scene adds board Z0.68468mm. Render shows separate bows and guides.

## Genuine qualification holds
Actual cable OD/bend/fatigue limits, precise mated PH/SH seating/exit tolerances,195mm OLED/support tolerance margin, printed fit/strength and guide wear remain unqualified. No connector relocation or renewed part/knob approval is required for nominal CAD. Prior encoder seating/load, knob bore and electrical holds unchanged. **Heater DO NOT ENERGIZE.**

## Installed source URLs
- https://cdn.flux.ai/document_assets/oled-bow-r15-e7759c06-31da-463e-afa1-561bc1424b90.build123d
- https://cdn.flux.ai/document_assets/encoder-bow-r15-83c8f6e8-571a-4ff0-b99e-f28600724c6b.build123d
- https://cdn.flux.ai/document_assets/oled-loose-guide-326657e6-e451-44f6-8839-099b9bf5d366.build123d
- https://cdn.flux.ai/document_assets/encoder-loose-guide-relieved-0b504d80-1aa0-4a6e-8b79-828f0835100b.build123d
